The Diesel Truck Site  

Go Back   The Diesel Truck Site > Diesel Truck Forums > Chevrolet & GMC Duramax Forum > Chevrolet & GMC Duramax Tech Articles


Reply
 
Thread Tools Display Modes
  #1  
Old 12-22-2010, 06:58 PM
MnTom's Avatar
MnTom MnTom is offline
Administrator
 
Join Date: Nov 2010
Location: Near Duluth, Mn
Posts: 4,899
Default Front Wheel Bearing Replacement on the Duramax

This write up was posted by McRat over on The Diesel Garage

Front Wheel Bearing Replacement on the Duramax. Preface: If you are running oversized tires, high hp, or subjecting your truck to extreme shocks on the front, like drag racing or sled pulling, your front wheel bearings will not last much past the 36k mi warranty.

You can tell if the wheel bearing is shot by jacking the truck up til the wheel is off the ground, grabbing the top and bottom of the tire and try to pry it in and out. ANY movement is wear. A stocker will not move. Ours were worn to the point of more than 2" slop at the tire with 50,000mi on the truck. You can drive pretty far worn bearings without fear of the wheel departing the truck due to the captive design of the unit.

This is a sealed bearing assy that includes the hub, lug bolts, bearings, axle spline, wheel speed sensor, and cable. GM has recently updated the part number to #15225770 or AC Delco #FW289. Retail for the unit can be as high as $450 ea, to a low of $150 ea, so it pays to shop around.

You will need:

Floor jack
Jack stand
15mm socket and ratchet, wrench will work if you are strong.
21mm socket and BIG *** breaker bar. Cutting torch will have better luck than a wrench on this *****.
36mm socket and breaker bar. Nut is actually 35.5mm, so a 1 3/8" socket can be beaten on it.
Sharp flat blade screwdriver.
Hammer.
Pliers.
Large C-Clamp.
Grease.
Loctite - Blue. Unless you're selling it, then use red. Blue allows for removal in the future, red is REALLY aggressive.
Not absolutely necessary - impact wrench.

Step 1:
Jack side of truck up, and put a jackstand under it. Use frame rail.
Turn ignition to ON position and put in 4wd Hi, and set parking brake.
Remove Wheel.

Step 2:
Unplug the wheel sensor wire near the top of the shock. There are 4 push in wire retainers, you will not save them, so rip them out with pliers. You can cut off the wire if you think it will get in your way.

Step 3:
Use C-Clamp to compress the brake pistons so it will be easy to reinstall.

Step 4:
There are 2 loctited 21mm head bolts that hold the brake caliper frame to the axle support. THESE ARE TIGHT!!! Rotate the steering to get to them easier. Remove the bottom, then loosen the top one so you can remove it with your fingers. You will need to have something ready to support it when you remove the brake assy.

Step 5:
Pull the top bolt and set the brake assy on something that will not stress the brake line. You can destroy a brake line by hanging that much weight on it.

Step 6:
Two lugs have a retaining washer that holds the disc on the hub for assembly purposes. Remove these by rotating them with a screwdriver, then pry them off. You do not need these, I suggest you throw them away. Once they are removed, you can pull the disc off the hub. If it does NOT come off easy? Torch and a mallet. Do not hit the rotor with a steel hammer or you can burr it up.


Step 7:
Pry the center dust cover off with a sharp flat blade screwdriver. Be fairly gentle as you will reuse this. It's not REALLY necessary, and serves no function whatsoever, but it looks prettier than the axle nut.


Step 8:
That nut in the center keeps the axle from wandering too deep into the differential. Other than that, it does nothing. It is not a load component. It measures 35.5mm, you can remove it with a 36mm socket and breaker bar or tap a 1 3/8" socket onto it. If the truck is in 4WD with the truck in park, it will not spin the hub. The nut is a locking nut, so it will be tight most the way off.

Step 9:
Once the nut is off, spray some WD40 into the center spline, then tap the axle into the hub gently until it stops. It will move about 1". This will make it easy to pull the hub off when it's time.

Step 10:
There are four 15mm bolts that hold the hub on. These are also pretty tight. If you turn the steering, it makes them easier to remove.


Step 11:
The hub should slip right out. You might have to tap the axle a bit more while holding the hub out from the base. Clean all mating surfaces, grease the axle spline and o-ring in base. Dust shield faces forward.

INSTALLATION:
Here's the new hub/bearing assy. There is some electrical tape on the wire holding them together, tear it off.

Line up the spline to the holes with the wire at TDC. If the bolt holes do not line up, you can either take the truck out of 4WD, or pull it off the spline and try to align it better. I suggest align it better. There is a lot of slop in the axle rotation, so you don't have to precisely get the right tooth on the spline for it line up. Screw the axle nut on by hand to hold it in place.

Use a few drops of Blue Loctite (yes I know it comes in a red bottle ) on the 15mm bolts, and bolt the hub back down. Don't forget the dust shield. The wire goes UNDER the tab on the dust shield.

Tighten down the axle nut and washer on the axle. Tap the dust cover back on with the handle of the hammer.

Replace the rotor.

Hold the brake pads apart with your fingers and slide the brake assy onto the rotor. Use loctite and reinstall the two 21mm bolts. Do I know the torques? Uh... REAL tight?

Snap the 4 wire holders into the same holes the old one came out of, and reconnect the connector near the shock.

Put wheel back on, lower truck..

IMPORTANT

Start engine and pump the brakes slowly several times. When you pushed the pistons back into the calipers, they are still sitting far away from the rotors and YOU WILL HAVE NO BRAKES. Pump the pedal slowly until the pedal feels firm.

Road test.
__________________
1996 RAM "Custom Ground" 100 plate 3/4 forward, 300 injectors, 16.5 timing, Goerends Auto = 365HP, 833TQ Third Gen Rims, Aluminum Headache Rack
Duct Tape can't fix stupid, BUT it can muffle the sound
Reply With Quote
  #2  
Old 12-22-2010, 09:02 PM
stodg73's Avatar
stodg73 stodg73 is offline
Out There, Savin' Lives
 
Join Date: Nov 2010
Location: Southern Colorado
Posts: 2,309
Default

This needs to be moved to the Chevrolet/Dmax Section.
__________________
O.O., 01.5, Dodge, 2500, High Output (H.O.) Cummins Turbo Diesel (245/505), Quad Cab Long Bed (QCLB), 4x4, Sport, Original Bosch VP 44 Injection Pump, 6 Speed/NV5600 Transmission, 3.55 Gears, 105k, currently stock engine, Fram Air Filter, 285/75R16s, Glow Shift Gauges: Fuel Pressure (FP), Boost, Exhaust Gas Temperature (EGT), Oil Temperature, SMARTY@1, Airtex lift pump 19 psi @ idle, 14 psi @ WOT, Propane Injection, 2 Stroke Oil, Intake Air Temperature (IAT) Fooler = Better MPG, Bed Lined, Chrome Nerf Bars, more to come!!

Toys:
'79 CJ5, 258ci, 3" lift, 33x12.50x15, Stock Engine and 3 Speed Tranny
'05 Suzuki, GSX1300R, Hayabusa, All Stock, #3('00 blown engine, '00 stolen, & '05)
The complete live & learn and pass it on by H. Jackson Brown, Jr.
Reply With Quote
  #3  
Old 12-22-2010, 09:07 PM
MnTom's Avatar
MnTom MnTom is offline
Administrator
 
Join Date: Nov 2010
Location: Near Duluth, Mn
Posts: 4,899
Default

Quote:
Originally Posted by stodg73 View Post
This needs to be moved to the Chevrolet/Dmax Section.
OOpppsss..... Sorry
__________________
1996 RAM "Custom Ground" 100 plate 3/4 forward, 300 injectors, 16.5 timing, Goerends Auto = 365HP, 833TQ Third Gen Rims, Aluminum Headache Rack
Duct Tape can't fix stupid, BUT it can muffle the sound
Reply With Quote
  #4  
Old 12-22-2010, 10:51 PM
stodg73's Avatar
stodg73 stodg73 is offline
Out There, Savin' Lives
 
Join Date: Nov 2010
Location: Southern Colorado
Posts: 2,309
Default

Just saw that it was in the wrong section.
__________________
O.O., 01.5, Dodge, 2500, High Output (H.O.) Cummins Turbo Diesel (245/505), Quad Cab Long Bed (QCLB), 4x4, Sport, Original Bosch VP 44 Injection Pump, 6 Speed/NV5600 Transmission, 3.55 Gears, 105k, currently stock engine, Fram Air Filter, 285/75R16s, Glow Shift Gauges: Fuel Pressure (FP), Boost, Exhaust Gas Temperature (EGT), Oil Temperature, SMARTY@1, Airtex lift pump 19 psi @ idle, 14 psi @ WOT, Propane Injection, 2 Stroke Oil, Intake Air Temperature (IAT) Fooler = Better MPG, Bed Lined, Chrome Nerf Bars, more to come!!

Toys:
'79 CJ5, 258ci, 3" lift, 33x12.50x15, Stock Engine and 3 Speed Tranny
'05 Suzuki, GSX1300R, Hayabusa, All Stock, #3('00 blown engine, '00 stolen, & '05)
The complete live & learn and pass it on by H. Jackson Brown, Jr.
Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:35 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
Skin & Style Created By: Mopar1973Man.Com
Copyright 2012 Diesel Truck Site